One-rep max
Estimate the most weight you could lift for one repetition from a recent working set.
Estimated one-rep max
How a one-rep max estimate works
How it works
A true one-rep max is the heaviest weight you can lift once with good form, but testing it is tiring and risky if you are unprepared. This calculator works backwards from a set you already completed: the heavier the weight and the fewer reps you managed, the closer you were to your limit. It averages two well-known formulas, Epley and Brzycki.
The two formulas disagree slightly on purpose, and that disagreement is useful. Epley tends to give the higher estimate as reps climb, while Brzycki tends to give the lower one, so averaging them lands in the middle of the credible range instead of trusting one model completely. The calculator then rounds to the nearest plate-friendly increment — 2.5 kilograms or 5 pounds — because a training plan needs a weight you can actually load on the bar.
What counts as a good input set matters as much as the formula. The set should be genuinely challenging, taken close to the point where another rep would have failed or form would have broken down, with full range of motion. An easy set of 8 tells the formulas very little, and the estimate will come out low. A hard set of 4 tells them a lot.
Formula: Epley estimates 1RM as weight times (1 plus reps divided by 30). Brzycki estimates it as weight times 36 divided by (37 minus reps). This calculator averages the two and rounds to the nearest plate-friendly increment, 2.5 kilograms or 5 pounds.
Worked example
Lift 80 kilograms for 6 reps and Epley gives 96 kilograms, while Brzycki gives about 92.9 kilograms. Averaging them gives roughly 94.5 kilograms, which rounds to a 95-kilogram estimated max. From there, 90 percent is about 85 kilograms for sets of 3 to 4 reps, and 70 percent is about 67.5 kilograms for sets of 10 to 12.
Here is a worked example in pounds. Lift 225 pounds for 4 reps. Epley gives 225 times 1 plus 4 divided by 30, which is 255 pounds. Brzycki gives 225 times 36 divided by 33, which is about 245.5 pounds. Averaging them gives about 250 pounds, which is already a plate-friendly number. From there, 90 percent is 225 pounds for sets of 3 to 4 reps, and 80 percent is 200 pounds for sets of 7 to 8.
Notice what happens with a single rep: if you enter 1 rep, the estimate is simply the weight you lifted, because you have already demonstrated that maximum. The formulas only earn their keep when the input set has two or more reps.
How to read your result
| Percentage of max | Weight (95 kg example) | Typical use |
|---|---|---|
| 100% | 95 kg | Estimated maximum, one rep. |
| 90% | 85 kg | Heavy strength work, 3 to 4 reps. |
| 80% | 75 kg | Strength and muscle, 7 to 8 reps. |
| 70% | 67.5 kg | Volume work, 10 to 12 reps. |
These percentages match the training weights the calculator shows with your result. They are planning numbers: on a tired day the same percentage will feel heavier, and on a fresh day lighter, so let bar speed and form have the final say.
Limitations
Estimates are lift-specific. The formulas were built largely around barbell lifts like the squat, bench press, and deadlift, and they transfer less well to machines, single-arm work, or lifts where balance and technique dominate. Beginners also get shakier estimates, because their limiting factor is often coordination rather than strength — the weight they can handle for 6 reps understates what their muscles could do with better practice.
High-rep sets are the other weak spot. Above about 12 reps, endurance contributes as much as strength, the two formulas drift further apart, and the calculator flags the result as lower confidence. When that flag appears, retest with a heavier set of 3 to 6 reps for a number you can plan around.
Common questions
- Which rep range gives the best estimate? Sets of 3 to 6 reps are the sweet spot. Above 10 to 12 reps, endurance matters as much as strength, so the estimate gets shakier and the calculator flags lower confidence.
- Can I jump straight to my estimated max? No. Treat it as a planning number, not a dare. Build up gradually, use a spotter and safety bars for heavy barbell work, and stop a set when your form breaks down.
- Does it work for every lift? Best for the main barbell lifts. It is less reliable for Olympic lifts, machines with assistance, and lifts where technique fails before strength does. Treat those results as rough guides only.
- Why average two formulas instead of picking one? No single formula is right for everyone. Epley and Brzycki bracket the likely range, so their average is less likely to be badly wrong than either one alone.
- How often should I retest my estimate? Every four to eight weeks, or after a training block, using a fresh hard set. Retesting weekly just adds noise; strength changes over weeks, not days.